Sharrow’s wide selection of rigging hardware is ready to match any of your lifting needs.
Our inventory includes shackles, turnbuckles, plate clamps, eye fittings, latch kits, sheaves and pulleys, blocks, swivels, hooks, rings/links, and so much more.
Sharrow’s expertise and product knowledge ensure you will receive the proper component to match your application.
Anchor shackles are the most common and most versatile shackle available, with uses ranging from tie-down, towing, suspension or lifting applications. Some anchor shackles even allow for angle loading when gathering more than one sling in the bow. Anchor shackles are available in painted or galvanized, and with screw pin or bolt-type connectors. For lessor critical connections, round-pin style connectors are also available. Capacities range from 1/3 to 55 metric ton.
Chain shackles have uses ranging from tie-down, towing, suspension or lifting applications. However, they may never be side- or angle-loaded. Chain shackles are designed for inline tension only. Chain shackles are available in painted or galvanized, and with screw pin or bolt-type connectors. For less critical applications, round-pin style connectors are also available. Capacities range from 1/3 to 55 metric ton.
Wide-body shackles connect high-strength synthetic web slings, high-strength synthetic round slings or wire rope slings to each other or to your load. All sizes are quenched and tempered for maximum strength. These heavy duty shackles are factory proof tested and available in capacities ranging from 7 to 1,550 metric tons.
Long reach shackles are for use in applications where a longer reach is needed to attach to pick points. This type of shackle is designed for in-line applications only, and should never be side loaded. Capacities range from 3-1/2 to 25 US tons.
Web Shackles, also known as “Sling Saver” shackles, have a special bow which allows for more efficient distribution of the load across the fibers of the sling to allow for 100% of the sling’s capacity. These are available in both screw pin or bolt type styles, and range in capacity from 3-1/4 to 50 metric tons.
Recommended for straight or inline pull only. Available in the following configurations to meet your application needs. Depending on the configuration chosen, turnbuckles are available in nominal sizes starting at 1/4" up to 2-3/4” with capacities up to 75,000 pound working load limits.
Plate clamps are available in a variety of styles and capacities with various options to handle your specific plate lifting, turning and positioning needs. Sharrow can help if you need a new clamp, repair part or your clamp repaired.
Vertical plate clamps are available in standard or non-marring and are used for lifting, turning, moving or vertical transfer of sheet, plates, or fabrications from horizontal to vertical and down to horizontal (180°) as needed. Vertical clamps are generally available with capacities from 0.25 to 30 metric tons. Custom engineered clamps are also available.
Horizontal plate clamps are available in locking, pre-tension, and non pre-tension styles and are generally used to attach to material for horizontal lifting and transfer. Models available for transferring rigid material and sagging material, and for material that must not be marred or scratched. These clamps must be used in pairs or more. Size and weight capacities vary widely. Custom engineered clamps are also available.
Positioning screw clamps are suitable for positioning, pulling and turning steel plates and sections. They are available in capacities of 1.5 and 3 metric tons
Sharrow offers the most complete line of eye fittings, including eye bolts, pad eyes, eye nuts and swivel hoist rings. Below are some of the most popular styles. If you need a particular eye fitting but do not see it here, or have a question about an application, please contact our customer service department directly. Our staff will help locate exactly what you need.
Many different styles of latch kits are available, depending on application. All feature high cycle, long-life spring. Hook latch kits ship unassembled and individually packaged with instructions.
Roll-forged common bore sheaves are available in sizes up to 78” diameter. Common bore sheaves are machined for a running fit for the shaft size listed.
Bronze brushed roll-forged sheaves are available in sizes up to 78” diameter. Bronze-brushed sheaves are equipped with S.A.E. 660 bronze brushings for cold-finished shafts with “figure 8” oil groove.
Roller bearing roll-forged sheaves are available in sizes up to 78” diameter. Roller bearing sheaves are designed to operate on shafts carbonized to 60 Rockwell C and groove to +/- .000.
Tapered roll-forged roller bearing sheaves are available in sizes up to 78” diameter. Tapered roller bearing sheaves are designed to operate on shafts machined to +/- .0005 of the indicated shaft size.
Light duty, or snatch blocks, are used as a pulling assembly to increase the load pulling capacity of a winch. Available in a wide range of configurations, materials and capacities for your specific need.
Suitable for frequent rotation under load. All swivels individually proof-tested. Not to be used on demolition (wrecking) balls.
Designed for maximum strength without weight or bulk. All swivels individually proof-tested.
Sharrow offers the most complete line of hooks, which are designed to provide maximum strength without excessive weight and bulk. Below are some of the most popular styles. If you need a particular hook but do not see it here, or have a question about an application, please contact our customer service department directly. Our staff will help locate exactly what you need.
Oblong rings and links are individually proof tested to values shown with certification. Weldless available.
Pear-shaped rings and links are individually proof tested at 2 times working load limit with certification. Weldless available.
