Summit Lifting Devices · a division of Sharrow Lifting Products
Build-a-Spreader-Bar
Set the load, the spread and the chain angle. The drawing follows your numbers, tells you the headroom you need above the bar, and sends the lift to the engineer who sizes it.
Reference drawing
Headroom 83.1" above the ears
Drag the drawing sideways to see the whole bar.
Your specification
5 ton · 96" span · 60°
5-ton WLL (10,000 lb), 96" fixed span, 60° chain legs to a master link, swivel hook with latch under each end, 5,774 lb per leg at the widest setting
- Chain per leg
- 96"
- Headroom needed
- 83.1"
- Load per leg
- 5,774 lb
Built to ASME BTH-1, the standard for below-the-hook lifting devices. Every bar is signed off by our engineer against your actual lift before anything is cut, and the finished bar ships with its load test and certificate. A spreader bar is squeezed rather than bent, so the section depends on buckling over the whole spread — our engineer picks it for your lift. Everything drawn above, span, chain, angle and headroom, is to your numbers.
Quote this spreader barSends the drawing’s full spec to our sales desk. No obligation, and nobody will phone you about a bar you were only curious about.
Beam or bar?
They fail in opposite directions
People use the words interchangeably and they are not the same tool. Picking the wrong one is the most common mistake we see on a below-the-hook enquiry.
A lifting beam is bent
One hook above, pick points below, and the load tries to fold the beam in the middle. It needs almost no headroom, which is usually why you want one. Deeper section, heavier for the same span.
Build a lifting beam →A spreader bar is squeezed
Two slings or chains down to the ends of the bar, so the lift puts the bar into compression instead of bending. Lighter for a long spread, but it needs real headroom above the load, and the flatter the legs the harder it is squeezed.
How we quote one
The drawing is yours, the section is ours
Span, chain length, angle and headroom on the drawing are exactly what you typed, so you can check the geometry against your building before anyone picks up a phone. What the bar is made from is the part we work out, because a compression member is governed by buckling over the whole spread and there is no honest way to read that off a web page.
- Fixed length, or telescoping with a pin for several spreads
- Quarter ton to forty tons, 24" to 240" hook to hook
- Chain legs to a master link, swivel hook and latch under each end
- Designed to ASME BTH-1 and signed off before anything is cut
- Proof load tested, with the certificate in the box
- Fabricated in Little Canada, not drop-shipped
Summit Lifting Devices · a division of Sharrow Lifting Products
Not the shape you need?
You are on one of four. The other builders draw themselves the same way, and the fourth is for everything no web page can draw — send a drawing, a CAD file, or a photo of a sketch.
Build‑a‑Beam
One hook above, pick points below, for when you have almost no headroom to work with. Sizes the channel to the load as you go.
Half a ton to 10 tons · 24" to 240" span
Start buildingBuild‑a‑Spreader‑Bar
Two legs down to the ends of a bar, so the lift squeezes it instead of bending it. Lighter over a long spread, but it wants real headroom.
A quarter ton to 40 tons · 24" to 240" spread
Start buildingBuild‑a‑Triangle‑Beam
A beam cut from flat plate: a hole at the top for the hook, holes along the bottom for the load. For lugs the stocked sizes do not match, or more than two pick points.
A quarter ton to 20 tons · 12" to 60" pick spacing
Start buildingFully customSomething else entirely
C-hooks, coil and sheet handling, tilt frames, a fixture for one awkward part. Send a drawing, a CAD file, or a photo of a sketch and our engineer takes it from there.
A napkin sketch is enough to start
Send a drawingSummit does not make everything, and custom is not always what you want. If a catalogue part already fits, it comes with a part number, a published capacity and no engineering lead time — we carry Caldwell, Peerless, M&W and Renfroe too, and we will say so.
Not sure it's a spreader bar you need?
Tell us what you're picking up, how big it is and what the headroom looks like. If a lifting beam or something off the shelf does it cheaper, we'll say so.

