Summit Lifting Devices · a division of Sharrow Lifting Products
Build-a-Triangle-Beam
A beam cut from flat steel plate, with a hole at the top for the hook and holes along the bottom for the load. Set the spacing and the drawing follows your numbers — including an off-centre pick when the load will not balance.
Reference drawing
Your beam: 1-ton WLL (2,000 lb), 24" pick spacing, 11.53" overall height, plate construction, 3" x 5" oblong hole (slot) top pick point, 2 lower pick points, leg lengths 19.48" / 19.48"
Built to ASME BTH-1, the standard for below-the-hook lifting devices. Every beam is signed off by our engineer against your actual lift before anything is cut, and the finished beam ships with its load test and certificate. A triangular beam carries its load through the steel around the holes, so the thickness, the hole sizes and the edge distances come from our engineer, not from this page. Everything drawn above — pick spacing, height and hole positions — is to your numbers.
Start here first
If your spacing is 12, 24 or 36 inches, buy the stocked one
We carry the standard triangular plate beams in three spacings and seven capacities, from 500 lb to 80,000 lb. A stocked part has a part number, a published headroom, a known weight and no engineering lead time. This page cannot give you any of those, so it is worth thirty seconds to check the catalogue before you ask us to build one.
When a custom one is the right answer
Three things the catalogue cannot do
These are the cases worth building for. Everything else is usually a stocked part in disguise.
A spacing that is not 12, 24 or 36
Lugs on a weldment, lifting eyes on a casting, a fixture that was never built around a catalogue part. The holes go where your load already has them.
A load that will not balance
Move the top hole off centre and it sits over the real centre of gravity, so the load comes up level instead of hanging crooked. No catalogue part offers this.
More than two lower points
Up to nine holes along the bottom edge, so one beam covers several loads, or spreads a long one across more than two attachment points.
How we quote one
The drawing is yours, the steel is ours
Pick spacing, overall height and hole positions on the drawing are exactly what you typed, measured between things you can put a tape on. What it is made from is the part we work out: a triangular beam carries its load through the steel around the holes, so plate thickness, hole sizes and edge distances are an engineer's job and there is no honest way to read them off a web page.
- Flat plate, round or slotted top pick point
- Quarter ton to forty tons, 12" to 60" pick spacing
- Two to nine lower pick points, 3" apart at the closest
- Off-centre top hole for an unbalanced load
- Designed to ASME BTH-1 and signed off before anything is cut
- Proof load tested, with the certificate in the box
Summit Lifting Devices · a division of Sharrow Lifting Products
Not the shape you need?
You are on one of four. The other builders draw themselves the same way, and the fourth is for everything no web page can draw — send a drawing, a CAD file, or a photo of a sketch.
Build‑a‑Beam
One hook above, pick points below, for when you have almost no headroom to work with. Sizes the channel to the load as you go.
Half a ton to 10 tons · 24" to 240" span
Start buildingBuild‑a‑Spreader‑Bar
Two legs down to the ends of a bar, so the lift squeezes it instead of bending it. Lighter over a long spread, but it wants real headroom.
A quarter ton to 40 tons · 24" to 240" spread
Start buildingBuild‑a‑Triangle‑Beam
A beam cut from flat plate: a hole at the top for the hook, holes along the bottom for the load. For lugs the stocked sizes do not match, or more than two pick points.
A quarter ton to 20 tons · 12" to 60" pick spacing
Start buildingFully customSomething else entirely
C-hooks, coil and sheet handling, tilt frames, a fixture for one awkward part. Send a drawing, a CAD file, or a photo of a sketch and our engineer takes it from there.
A napkin sketch is enough to start
Send a drawingSummit does not make everything, and custom is not always what you want. If a catalogue part already fits, it comes with a part number, a published capacity and no engineering lead time — we carry Caldwell, Peerless, M&W and Renfroe too, and we will say so.
Send us the lift, not just the beam
Tell us what is being lifted and where it picks up, and our engineer sizes the beam against that rather than against a guess.

